=======================================================
MSDS Safety Information 
=======================================================

NAME: 850 ACRYLIC LATEX CAULK
 
=======================================================


MATERIAL SAFETY DATA SHEET
MSDS Name: PB-3 SILICONIZED ACRYLIC LATEX CAULK
MSDS Number: 16711-001
Version Number 2
MSDS Date: OCT-01-2006
Page Number: 1
-----------------------------------------------------------------------------
SECTION I - PRODUCT AND COMPANY INFORMATION
Product Name: PB-3 SILICONIZED ACRYLIC LATEX CAULK
HMIS Hazard Rating: Health: 1 Fire: 0 Reactivity: 0 PPE: B
Company Identification: SILCO, INC.
7561 TYLER BLVD. UNIT 6
MENTOR OH 44060
Information phone/Fax: (440) 975-8886 (440) 975-8887
Product Class CAULK
SECTION II - INGREDIENT AND HAZARD INFORMATION
Hazardous Ingredient Name CAS Number Percent TSCA
Titanium Dioxide ** 13463-67-7 < 5.0 Y
ETHYLENE GLYCOL 107-21-1 < 2.0 Y
MINERAL SPIRITS 64742-48-9 < 2.0 Y
Ingredient Notes:
Remaining ingredients are not considered OSHA hazardous.
**The main hazard for Titanium Dioxide is dust inhalation. Because of
its incorporation into the caulk, exposure by inhalation is unlikely.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
SECTION III - PHYSICAL AND CHEMICAL PROPERTIES
Form: High viscosity caulk
Appearance/Color: various colors
Solubility (in water): yes
pH Value, +/-.3: 7.5
--------------------------------------------------------------------------------
MATERIAL SAFETY DATA SHEET
MSDS Name: PB-3 SILICONIZED ACRYLIC LATEX CAULK
MSDS Number: 16711-001
Version Number 2
MSDS Date: SEP-09-2002
Page Number: 2
-----------------------------------------------------------------------------
Boiling Range: 212.øF (100.øC)
Vapor Pressure (mmHg): 15.@ 68.øF (20.øC)
Evaporation Rate: 0.5 times Slower than n-Butyl Acetate
Vapor Density: Heavier than air
% Volatile, Weight approx. 20.%
% Volatile, Volume approx. 30.%
Specific Gravity: 1.556
VOC (less H2O or exempt) 41 Gr/L (2%)
NOTE:
Odor : Mild acrylic odor. Freeze Point : 32 Deg F
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
SECTION IV - FIRE FIGHTING MEASURES (Flash,UEL,LEL for solvent only)
Flammability Class N/A
Flash Range: Not Available
Explosive Range (LEL/UEL): Not Applicable
EXTINGUISHING MEDIA:
Dry chemical -- Carbon Dioxide -- Foam -- Water Fog
Will not burn in wet state.
SPECIAL FIRE-FIGHTING PROCEDURES:
Water may be used to cool and protect exposed containers.
Caution should be taken because uncured material is water soluble.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
Any closed container may burst when exposed to extreme
heat or fire.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
SECTION V - HEALTH HAZARD DATA
ROUTES OF ENTRY:
ENTRY THROUGH...Inhalation and skin most likely
CARCINOGENICITY...
NTP? N/E | IARC Monographs? N/E | OHSA? NO
EFFECTS OF OVEREXPOSURE
Inhalation: May irritate respiratory tract.
Skin/Eye Contact: May cause irritation.
Ingestion: Swallowing large amounts may cause nausea,
vomiting. ( an unlikely route of entry )
--------------------------------------------------------------------------------
MATERIAL SAFETY DATA SHEET
MSDS Name: PB-3 SILICONIZED ACRYLIC LATEX CAULK
MSDS Number: 16711-001
Version Number 2
MSDS Date: SEP-09-2002
Page Number: 3
-----------------------------------------------------------------------------
FIRST AID MEASURES
Inhalation: If affected by inhalation, remove to fresh air.
Eye Contact: Flush with water for at least 15 minutes, and
get prompt medical attention.
Skin Contact: Wash skin thoroughly with soap and water.
Ingestion: Drink water, and get medical attention.
-------------------------------------------------------------------
N/A= Not applicable N/AV=Not available N/E, N/est=Not established
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
SECTION VI - STABILITY AND REACTIVITY
Stability: This product is stable
Hazardous Polymerization: Hazardous polymerization will not occur
INCOMPATABILITY:
None
CONDITIONS TO AVOID:
None
HAZARDOUS DECOMPOSITION PRODUCTS:
May produce oxides of carbon and oxides of nitrogen when burned.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
SECTION VII - ACCIDENTAL RELEASE AND DISPOSAL MEASURES:
STEPS TO BE TAKEN IN CASE OF SPILL:
Wear appropriate protective clothing. Add dry absorbent and
shovel or sweep up. Place in an appropriate container and seal.
WASTE DISPOSAL METHOD:
Dispose of in accordance with Federal, State, and Local regulations.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
SECTION VIII - EXPOSURE CONTROLS/PERSONAL PROTECTION
Occupational Exposure Limits
ACGIH TLV ACGIH TLV-C ACGIH STEL OSHA STEL OSHA PEL
Titanium Dioxide **
10.00 mg/F3 N/est N/est N/est 15.00 mg/F3
ETHYLENE GLYCOL
50.00 PPM N/est N/est N/est 50.00 PPM
MINERAL SPIRITS
100.00 PPM N/est N/est N/est 100.00 PPM
--------------------------------------------------------------------------------
MATERIAL SAFETY DATA SHEET
MSDS Name: PB-3 SILICONIZED ACRYLIC LATEX CAULK
MSDS Number: 16711-001
Version Number 2
MSDS Date: SEP-09-2002
Page Number: 4
-----------------------------------------------------------------------------
RESPIRATORY PROTECTION:
NIOSH respirators recommended if vapors and mists are generated.
VENTILATION:
Local exhaust is recommended for safe practice.
PROTECTIVE CLOTHING:
Gloves and clothing should be worn to prevent repeated skin contact.
EYE PROTECTION:
Splashproof goggles or safety glasses should be worn.
HANDLING AND STORAGE PRECAUTIONS:
Keep from freezing. Keep away from heat.
Keep containers closed when not in use.
Avoid prolonged or repeated contact with skin.
Keep out of the reach of children.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
SECTION IX - TRANSPORT INFORMATION:
DOT CLASSIFICATIONS FOR ONE GALLON AND UNDER CONTAINERS
DESCRIPTION: Non-hazardous
DOT CLASSIFICATIONS for OVER 1 GALLON size CONTAINERS
DESCRIPTION: Non-hazardous, Caulking product
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
SECTION X - REGULATORY INFORMATION:
SARA TITLE III SECTION 313:
This product contains the following toxic chemicals subject to the
reporting requirements of Section 313 of the Emergency Planning and
Community Right to Know Act of 1986 and of 40 CFR 372:
Ingredient Name CAS Number Percent
ETHYLENE GLYCOL 107-21-1 < 2.0
The following ingredients are registered for TSCA 12B
Ingredient Name CAS Number Percent
ETHYLENE GLYCOL 107-21-1 < 2.0
Ethylene Glycol fits the EPA Hazard Category definition of Immediate
(Acute) and Delayed (Chronic) Health Hazards under SARA Sect.311,312.
--------------------------------------------------------------------------------
MATERIAL SAFETY DATA SHEET
MSDS Name: PB-3 SILICONIZED ACRYLIC LATEX CAULK
MSDS Number: 16711-001
Version Number 2
MSDS Date: SEP-09-2002
Page Number: 5
-----------------------------------------------------------------------------
All chemical substances are TSCA listed.
California PROP.65 Chemicals: none known
DISCLAIMER:
The information contained herein is based on data available as of
the date of preparation of this MSDS and which we believe to be
reliable. However, no warranty is expressed or implied regarding
the accuracy of the data. We shall not be responsible for the use
of this information, or of any product, method, or apparatus mentioned,
and the user must make his own investigation to determine
the suitability of the information or products for his particular
purpose, for the protection of the environment, and the health and
safety of the users of this material.
--------------------------------------------------------------------------------
Last Page